- Subsonic filters what should it be turned at along with the other nobs to?
- Most all of them do, in fact, recommend precisely the placement you have adopted.
- What would be the final impedence of the Subs?
- Mount your amplifier on a solid surface that will not conduct electricity.
- If so how do I wire it up?
Another option is a dedicated crossover, but these can be tricky to work with, and quite expensive. Not knowing exactly which you have makes it impossible to give advice on what amplifier to use. Bridging refers to combining adjacent amplifier channels together, like in the diagram, and doesn't apply to subs or speakers.
Mike, I see what you mean - a web search came up with a few different amplifiers with different specs. The positive on the left side to the negative on the right side. You'll want to wire your gear together like this.
No Diagram Available
The sub is rated at w rms. Like everyone else, I want all I can get out of the amp, sydney asian but I don't want to burn it up. Not a clean crisp thump like I was hoping for.
For wiring subwoofers, we recommend using wires of to gauge in size. You should be alright as long as you never play distortion, trying to get louder bass. However, this rockford fosgate site does Is this accurate?
It Still Works
You can put it through an empty rubber grommet in a factory hole. That is the configuration I use and will continue to use. If you want a question answered about a system, it's best that you identify the gear by brand names and model numbers. Will this be enough power for the subs and what wiring do you recommend? Could you possibly provide a diagram of this to help me?
If you have a stock stereo and you have the remote wire there you want to in twine the remote wire with the power wire before inserting in the power slot for amp. If it is, and the amp's going into protection mode, then either something's wrong with the wiring or the amp. It can be connected to the negative battery side or somewhere metal in the car.
The only safe way to hook up your gear is to connect each subwoofer to a separate amplifier. Which is the best way to hook them up to get more bass or do I need a bigger amp? Hook it to a fuse connected to ignition turn on, like your accessory power fuse. It seems the mono's are cheaper. Why buy from an authorized dealer?
Don't forget to test your rem wire before you assume it works. Just wanted to know if this amp has enough to power these subwoofer without any damage to any of my equipment? The fuse amperage should match the gauge size. Without knowing which you have, we can't help with wiring.
- There's tons of info on all these subs on AudioAsylum.
- True low-bass somewhere around hz and below becomes very difficult to accurately locate the source of it.
- If you want left-right separation for your subs, two mono amps will work best.
Because once I put up a good amount of bass on the woofer it just turns off an turn on but right back off till I lower the bass knob. Joe, Not knowing exactly what amplifier or subwoofers you have make it impossible to give advice on how to wire them together. Gather your equipment Amp, Subs, Stereo, walk off the earth and wiring.
How to Install a Car Amp (with Pictures) - wikiHow
Or, you could wire one sub per terminal set, and then run two pairs of wires to the amp, it's electrically the same. How should i wire these for the best output? If the radio is good, and venus it could be a bad speaker.
What should I do if I want to play all my speakers through the amplifier? Caleb, You're definitely confusing issues by quoting max ratings which are meaningless. At peak demand, this system would try to draw amperes from your batteries and alternator. When connecting a line out connector to a factory head unit, it is advisable to use both sets of speaker wires to maintain the left and right stereo effect from modern music.
As an alternative, you could wire each sub to a set of output terminals. Which would provide the better sound? Installing an amp can be done without the help of a professional, allowing you to get great sound without an installation fee. Run your amp wires battery, ground.
How to Hook Up Subwoofers to an Amp
Do not attempt to install an amp if you do not feel comfortable with the procedure. How do I connect my new sub to my old amp? If you want a question answered about a system, it's best you identify the equipment in question by brand names and model numbers. Thank you for the help I greatly appriciate it. Don't expect a lot of bass out of that amplifier, though - its specs are a bit exaggerated.
Subwoofer Wiring Diagrams How to Wire Your Subs
Can you hook up a sub to a 2 channel stereo system
Would running stereo burn up the woofer? The amp has more than enough power to drive whatever model you have wired like this. Disconnect the negative battery terminal. Wood, The only safe way to connect that gear together is like this diagram.
How to Connect a Subwoofer to a Receiver or Amplifier
Manuel, matchmaking Your subs probably blew because they were being driven with twice their rated power. Would there be sufficient power? My question is what is the best way to wire the subs? The best way to get a question answered about a system is to identify the gear by brand names and model numbers so we can get the right information to you.
Video of the Day
It is best to install it as close as possible to the connection. Given the information above, which type of amp do you recommend and why? Dylan, Not knowing exactly what subwoofers you're referring to make it impossible to give advice on how to wire them together. Impedance is the amount of electrical resistance, or load, a sub puts up against an amplifier's output.
Okay, how will imaging be effected by a sub in the corner? Just pretend, in the upper diagram, that the two amps share the same chassis and do not need the extra power, ground, or turn-on lead wires. So I am looking at another sub or two. You can use this diagram as a wiring guide for your sub. Go to Corporate Sales page.